Beerpal Skrevet 24. mai 2017 Skrevet 24. mai 2017 Hei. Jeg sitter her nå og prøver meg litt på HS3 på dag 2. Men har satt meg fast på å legge til 2 stk Sunricher 4 kanals trådløs dimmebryter. Det eneste som kommer opp i "Device List" er "Sigma Generic Controller" med bilde av fullt batteri symbol og "No Status" Og her sitter jeg fast. Hvordan får jeg lagt til dette som bryter? Takk for flott forum. Mvh PH Siter
Moskus Skrevet 25. mai 2017 Skrevet 25. mai 2017 Hvis den blir listet som "Sigma Generic Controller" så har enten ikke HomeSeer ikke klart å hente ut all informasjon, eller så er enheten så ukjent (evt. dårlig programmert) at HomeSeer ikke finner noe (men det er sjeldent). Nøyaktig hvilken enhet er det? Er det denne? I så fall har jeg ikke hatt noen problemer med å legge den til selv, men du kan prøve å vekke den og kjøre en rescan (Root device -> Z-wave tab -> Rescan knapp). Siter
darkZ Skrevet 25. mai 2017 Skrevet 25. mai 2017 Har du noen feilmeldinger i loggen da? Jeg opplevde tilsvarende med en annen bryter forrige uke, løsningen hos meg var å flytte bryteren nærmere controlleren når jeg inkluderte.Sent from my iPhone using Tapatalk Siter
Beerpal Skrevet 25. mai 2017 Forfatter Skrevet 25. mai 2017 (endret) 2 timer siden, Moskus skrev: Nøyaktig hvilken enhet er det? Er det denne? I så fall har jeg ikke hatt noen problemer med å legge den til selv, men du kan prøve å vekke den og kjøre en rescan (Root device -> Z-wave tab -> Rescan knapp). Ja den ligner. Men den er kjøpt fra Intin. https://www.intin.no/produkt/sunricher-4-kanals-tradlos-dimmebryter/ Er ikke helt sikker hvor Root er? har prøvd flere ganger å trykket på den scan kanppen jeg finner her (Se bilde nederst) 1 time siden, darkZ skrev: Har du noen feilmeldinger i loggen da? Jeg opplevde tilsvarende med en annen bryter forrige uke, løsningen hos meg var å flytte bryteren nærmere controlleren når jeg inkluderte. Sent from my iPhone using Tapatalk Jeg har prøvd flere ganger slette den og legge den til igjen. Det ser ut som den får lagt til alle 5 gruppene til noden. ? men de synes ikke i "device list" mai-25 10:02:14 Z-Wave Node 5 supports the Wake-Up Command Class Version 2 - Capabilities were retrieved successfully. mai-25 10:02:14 Z-Wave Z-Wave Plus Association Root Group Information For Group 5 retrieved successfully from Node 5 Group Name=Launch 4, Profile Is General:Reserved And the group hosts 1 Event commands. mai-25 10:02:14 Z-Wave Z-Wave Plus Association Root Group Information For Group 4 retrieved successfully from Node 5 Group Name=Launch 3, Profile Is General:Reserved And the group hosts 1 Event commands. mai-25 10:02:13 Z-Wave Z-Wave Plus Association Root Group Information For Group 3 retrieved successfully from Node 5 Group Name=Launch 2, Profile Is General:Reserved And the group hosts 1 Event commands. mai-25 10:02:13 Z-Wave Z-Wave Plus Association Root Group Information For Group 2 retrieved successfully from Node 5 Group Name=Launch 1, Profile Is General:Reserved And the group hosts 1 Event commands. mai-25 10:02:12 Z-Wave Getting Z-Wave Plus Association Group Information (5 groups) from Node 5... mai-25 10:02:12 Z-Wave All associations for node 5 have been retrieved successfully, it supports associations on these groups: 1, 2, 3, 4, 5. mai-25 10:02:12 Z-Wave Node 5 Association Group 5 can have 20 associations, and currently has 1 mai-25 10:02:12 Z-Wave Node 5 Association Group 4 can have 20 associations, and currently has 1 mai-25 10:02:12 Z-Wave Node 5 Association Group 3 can have 20 associations, and currently has 1 mai-25 10:02:12 Z-Wave Node 5 Association Group 2 can have 20 associations, and currently has 1 mai-25 10:02:12 Z-Wave Node 5 Association Group 1 can have 1 associations, and currently has 1 mai-25 10:02:12 Z-Wave Getting association information for node 5 mai-25 10:02:12 Z-Wave Node 5 is a Z-Wave Plus node. Retrieving ZWPlus Info... mai-25 10:02:12 Z-Wave Node 5 is Z-Wave version: Lib: 4,33 App: 1.72 mai-25 10:02:12 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 10:02:12 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 10:02:12 Z-Wave Node: 5 Controls Class(es): SWITCH_BINARY, SWITCH_MULTILEVEL_V2 mai-25 10:02:12 Z-Wave Node: 5 Supports Class(es): ZWAVEPLUS_INFO_V2, ASSOCIATION, ASSOCIATION_GRP_INFO, VERSION_V2, MANUFACTURER_SPECIFIC, CONFIGURATION, DEVICE_RESET_LOCALLY, POWERLEVEL, BATTERY, WAKE_UP, FIRMWARE_UPDATE_MD mai-25 10:02:12 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 10:02:12 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 10:02:12 Z-Wave Syncing Z-Wave nodes with device list... mai-25 10:02:12 Z-Wave Found 4 Z-Wave nodes mai-25 10:02:12 Z-Wave Getting Z-Wave node list for network 0E0D0C0B... mai-25 10:02:07 Z-Wave Node 5 supports the Wake-Up Command Class Version 2 - Capabilities were retrieved successfully. mai-25 10:02:07 Z-Wave Z-Wave Plus Association Root Group Information For Group 5 retrieved successfully from Node 5 Group Name=Launch 4, Profile Is General:Reserved And the group hosts 1 Event commands. mai-25 10:02:07 Z-Wave Z-Wave Plus Association Root Group Information For Group 4 retrieved successfully from Node 5 Group Name=Launch 3, Profile Is General:Reserved And the group hosts 1 Event commands. mai-25 10:02:07 Z-Wave Z-Wave Plus Association Root Group Information For Group 3 retrieved successfully from Node 5 Group Name=Launch 2, Profile Is General:Reserved And the group hosts 1 Event commands. mai-25 10:02:06 Z-Wave Getting Z-Wave Plus Association Group Information (5 groups) from Node 5... mai-25 10:02:06 Z-Wave All associations for node 5 have been retrieved successfully, it supports associations on these groups: 1, 2, 3, 4, 5. mai-25 10:02:06 Z-Wave Node 5 Association Group 5 can have 20 associations, and currently has 1 mai-25 10:02:06 Z-Wave Node 5 Association Group 4 can have 20 associations, and currently has 1 mai-25 10:02:06 Z-Wave Node 5 Association Group 3 can have 20 associations, and currently has 1 mai-25 10:02:06 Z-Wave Node 5 Association Group 2 can have 20 associations, and currently has 1 mai-25 10:02:06 Z-Wave Node 5 Association Group 1 can have 1 associations, and currently has 1 mai-25 10:02:05 Z-Wave Getting association information for node 5 mai-25 10:02:05 Z-Wave Node 5 is a Z-Wave Plus node. Retrieving ZWPlus Info... mai-25 10:02:05 Z-Wave Node 5 is Z-Wave version: Lib: 4,33 App: 1.72 mai-25 10:02:05 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 10:02:05 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 10:02:05 Z-Wave Node: 5 Controls Class(es): SWITCH_BINARY, SWITCH_MULTILEVEL_V2 mai-25 10:02:05 Z-Wave Node: 5 Supports Class(es): ZWAVEPLUS_INFO_V2, ASSOCIATION, ASSOCIATION_GRP_INFO, VERSION_V2, MANUFACTURER_SPECIFIC, CONFIGURATION, DEVICE_RESET_LOCALLY, POWERLEVEL, BATTERY, WAKE_UP, FIRMWARE_UPDATE_MD mai-25 10:02:05 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 10:02:05 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 10:02:05 Z-Wave Syncing Z-Wave nodes with device list... mai-25 10:02:05 Z-Wave Found 4 Z-Wave nodes mai-25 10:02:05 Z-Wave Getting Z-Wave node list for network 0E0D0C0B... mai-25 10:01:44 Z-Wave Node 5 supports the Wake-Up Command Class Version 2 - Capabilities were retrieved successfully. mai-25 10:01:44 Z-Wave Z-Wave Plus Association Root Group Information For Group 5 retrieved successfully from Node 5 Group Name=Launch 4, Profile Is General:Reserved And the group hosts 1 Event commands. mai-25 10:01:43 Z-Wave Z-Wave Plus Association Root Group Information For Group 4 retrieved successfully from Node 5 Group Name=Launch 3, Profile Is General:Reserved And the group hosts 1 Event commands. mai-25 10:01:43 Z-Wave Z-Wave Plus Association Root Group Information For Group 3 retrieved successfully from Node 5 Group Name=Launch 2, Profile Is General:Reserved And the group hosts 1 Event commands. mai-25 10:01:42 Z-Wave Getting Z-Wave Plus Association Group Information (5 groups) from Node 5... mai-25 10:01:42 Z-Wave All associations for node 5 have been retrieved successfully, it supports associations on these groups: 1, 2, 3, 4, 5. mai-25 10:01:42 Z-Wave Node 5 Association Group 5 can have 20 associations, and currently has 1 mai-25 10:01:42 Z-Wave Node 5 Association Group 4 can have 20 associations, and currently has 1 mai-25 10:01:42 Z-Wave Node 5 Association Group 3 can have 20 associations, and currently has 1 mai-25 10:01:42 Z-Wave Node 5 Association Group 2 can have 20 associations, and currently has 1 mai-25 10:01:42 Z-Wave Node 5 Association Group 1 can have 1 associations, and currently has 1 mai-25 10:01:42 Z-Wave Getting association information for node 5 mai-25 10:01:42 Z-Wave Node 5 is a Z-Wave Plus node. Retrieving ZWPlus Info... mai-25 10:01:42 Z-Wave Node 5 is Z-Wave version: Lib: 4,33 App: 1.72 mai-25 10:01:42 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 10:01:42 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 10:01:42 Z-Wave Node: 5 Controls Class(es): SWITCH_BINARY, SWITCH_MULTILEVEL_V2 mai-25 10:01:42 Z-Wave Node: 5 Supports Class(es): ZWAVEPLUS_INFO_V2, ASSOCIATION, ASSOCIATION_GRP_INFO, VERSION_V2, MANUFACTURER_SPECIFIC, CONFIGURATION, DEVICE_RESET_LOCALLY, POWERLEVEL, BATTERY, WAKE_UP, FIRMWARE_UPDATE_MD mai-25 10:01:42 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 10:01:42 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 10:01:42 Z-Wave Syncing Z-Wave nodes with device list... mai-25 10:01:42 Z-Wave Found 4 Z-Wave nodes mai-25 10:01:42 Z-Wave Getting Z-Wave node list for network 0E0D0C0B... mai-25 09:59:58 Z-Wave Node 5 supports the Wake-Up Command Class Version 2 - Capabilities were retrieved successfully. mai-25 09:59:58 Z-Wave Z-Wave Plus Association Root Group Information For Group 5 retrieved successfully from Node 5 Group Name=Launch 4, Profile Is General:Reserved And the group hosts 1 Event commands. mai-25 09:59:58 Z-Wave Error Node 5 did not provide Wake-Up Command Class information - it will not be processed further. mai-25 09:59:52 Z-Wave Z-Wave Plus Association Root Group Information For Group 4 retrieved successfully from Node 5 Group Name=Launch 3, Profile Is General:Reserved And the group hosts 1 Event commands. mai-25 09:59:30 Z-Wave Z-Wave Plus Association Root Group Information For Group 3 retrieved successfully from Node 5 Group Name=Launch 2, Profile Is General:Reserved And the group hosts 1 Event commands. mai-25 09:59:25 Z-Wave Getting Z-Wave Plus Association Group Information (5 groups) from Node 5... mai-25 09:59:25 Z-Wave All associations for node 5 have been retrieved successfully, it supports associations on these groups: 1, 2, 3, 4, 5. mai-25 09:59:25 Z-Wave Node 5 Association Group 5 can have 20 associations, and currently has 1 mai-25 09:59:25 Z-Wave Node 5 Association Group 4 can have 20 associations, and currently has 1 mai-25 09:59:25 Z-Wave Node 5 Association Group 3 can have 20 associations, and currently has 1 mai-25 09:59:25 Z-Wave Node 5 Association Group 2 can have 20 associations, and currently has 1 mai-25 09:59:25 Z-Wave Node 5 Association Group 1 can have 1 associations, and currently has 1 mai-25 09:59:23 Z-Wave Getting association information for node 5 mai-25 09:59:23 Z-Wave Node 5 is a Z-Wave Plus node. Retrieving ZWPlus Info... mai-25 09:59:23 Z-Wave Node 5 is Z-Wave version: Lib: 4,33 App: 1.72 mai-25 09:59:23 Z-Wave Warning Error getting version information for node 5, Send failed. mai-25 09:59:18 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 09:59:18 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 09:59:17 Z-Wave Node: 5 Controls Class(es): SWITCH_BINARY, SWITCH_MULTILEVEL_V2 mai-25 09:59:17 Z-Wave Node: 5 Supports Class(es): ZWAVEPLUS_INFO_V2, ASSOCIATION, ASSOCIATION_GRP_INFO, VERSION_V2, MANUFACTURER_SPECIFIC, CONFIGURATION, DEVICE_RESET_LOCALLY, POWERLEVEL, BATTERY, WAKE_UP, FIRMWARE_UPDATE_MD mai-25 09:59:17 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 09:59:17 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 09:59:16 Z-Wave Syncing Z-Wave nodes with device list... mai-25 09:59:16 Z-Wave Found 4 Z-Wave nodes mai-25 09:59:16 Z-Wave Getting Z-Wave node list for network 0E0D0C0B... mai-25 09:59:16 Z-Wave Getting Z-Wave Plus Association Group Information (5 groups) from Node 5... mai-25 09:59:16 Z-Wave All associations for node 5 have been retrieved successfully, it supports associations on these groups: 1, 2, 3, 4, 5. mai-25 09:59:16 Z-Wave Node 5 Association Group 5 can have 20 associations, and currently has 1 mai-25 09:59:16 Z-Wave Node 5 Association Group 4 can have 20 associations, and currently has 1 mai-25 09:59:16 Z-Wave Node 5 Association Group 3 can have 20 associations, and currently has 1 mai-25 09:59:16 Z-Wave Node 5 Association Group 2 can have 20 associations, and currently has 1 mai-25 09:59:16 Z-Wave Node 5 Association Group 1 can have 1 associations, and currently has 1 mai-25 09:59:15 Z-Wave Getting association information for node 5 mai-25 09:59:15 Z-Wave Node 5 is a Z-Wave Plus node. Retrieving ZWPlus Info... mai-25 09:59:15 Z-Wave Node 5 is Z-Wave version: Lib: 4,33 App: 1.72 mai-25 09:59:15 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 09:59:15 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 09:59:14 Z-Wave Node: 5 Controls Class(es): SWITCH_BINARY, SWITCH_MULTILEVEL_V2 mai-25 09:59:14 Z-Wave Node: 5 Supports Class(es): ZWAVEPLUS_INFO_V2, ASSOCIATION, ASSOCIATION_GRP_INFO, VERSION_V2, MANUFACTURER_SPECIFIC, CONFIGURATION, DEVICE_RESET_LOCALLY, POWERLEVEL, BATTERY, WAKE_UP, FIRMWARE_UPDATE_MD mai-25 09:59:14 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 09:59:14 Z-Wave Z-Wave manufacturer information for node 5, ID: 0=0H (Sigma), Type: 3=3H, ID: 41733=A305H mai-25 09:59:14 Z-Wave Syncing Z-Wave nodes with device list... mai-25 09:59:14 Z-Wave Found 4 Z-Wave nodes mai-25 09:59:14 Z-Wave Getting Z-Wave node list for network 0E0D0C0B... mai-25 09:59:09 Z-Wave Device: Node 2 Z-Wave Luminance Set to 6 (Lux) mai-25 09:59:08 Z-Wave Device: Node 2 Z-Wave Temperature Set to 22,3 (C) mai-25 09:57:00 Device Control Device: Unknown Unknown New Device to Off (0) by/from: CAPI Control Handler mai-25 09:56:58 Device Control Device: Unknown Unknown New Device to On (100) by/from: CAPI Control Handler mai-25 09:56:57 Device Control Device: Unknown Unknown New Device to Off (0) by/from: CAPI Control Handler mai-25 09:56:56 Device Control Device: Unknown Unknown New Device to On (100) by/from: CAPI Control Handler mai-25 09:56:54 Device Control Device: Unknown Unknown New Device to On (100) by/from: CAPI Control Handler mai-25 09:56:53 Device Control Device: Unknown Unknown New Device to Off (0) by/from: CAPI Control Handler mai-25 09:56:51 Device Control Device: Unknown Unknown New Device to On (100) by/from: CAPI Control Handler mai-25 09:56:27 Z-Wave Starting Z-Wave Polling for Network 0E0D0C0B... mai-25 09:56:02 Web Server Web Server authorized local login successful from: 192.168.0.106 User: beerpal mai-25 09:56:01 TTS Speak ():Welcome to Home-Seer mai-25 09:56:01 Speaker Speaker host added, Name: hometroller Instance: Default IP address: 127.0.0.1 mai-25 09:56:01 Z-Wave ******************************************************************************* mai-25 09:56:01 Z-Wave STARTUP COMPLETE: All configured interfaces were successfully initialized. mai-25 09:56:01 Z-Wave ******************************************************************************* mai-25 09:56:00 Z-Wave UZB1: ...................................................................... mai-25 09:56:00 Z-Wave UZB1: .............................. FINISHED .............................. mai-25 09:56:00 Z-Wave UZB1: ...................................................................... mai-25 09:56:00 Z-Wave UZB1 is the SIS for the network. mai-25 09:56:00 Z-Wave UZB1 There is a SUC/SIS in the network. mai-25 09:56:00 Z-Wave UZB1 Controller is static lib. mai-25 09:56:00 Z-Wave UZB1 Controller chip type is ZW050x. mai-25 09:56:00 Z-Wave The interface's security support has been set. mai-25 09:56:00 Z-Wave UZB1: Z-Wave PC Controller is Type: Static Controller mai-25 09:56:00 Z-Wave UZB1: Z-Wave PC Controller Library Version: Z-Wave 4.05 (ZDK 6,51.6) mai-25 09:56:00 Z-Wave UZB1: Found 4 Z-Wave nodes in interface node ID 1 (UZB1) mai-25 09:56:00 Z-Wave UZB1: Z-Wave interface node ID: 1, Home ID: 0E0D0C0B mai-25 09:56:00 Z-Wave UZB1: Z-Wave Serial API version: 5 mai-25 09:56:00 Z-Wave UZB1: Z-Wave services for the SECURITY COMMAND CLASS were successfully started. mai-25 09:56:00 Info System connected to MyHS Service successfully. mai-25 09:55:59 Z-Wave UZB1: Controller firmware version: 5.6 mai-25 09:55:59 Z-Wave UZB1: Controller Manufacturer: PowerLynx, ID=0x1, Type=0x4 mai-25 09:55:59 Info System connected to MyHS Service, waiting for acknowledge... mai-25 09:55:59 Startup Start up complete. mai-25 09:55:59 Startup HSSentry is disabled in Setup, sentry will not be started. mai-25 09:55:59 Startup (Startup.vb script) No speaker clients detected, waiting up to 30 seconds for any to connect... mai-25 09:55:59 Startup (Startup.vb script) Scripting is OK and is now running Startup.vb mai-25 09:55:59 Startup Starting Event Scheduler... mai-25 09:55:58 Startup Running the startup script Startup.vb mai-25 09:55:58 HSTouch Server Server started on port 10200 mai-25 09:55:58 Info Starting speaker client... mai-25 09:55:58 Startup Starting DDNS service... mai-25 09:55:58 Startup Updater services starting... mai-25 09:55:58 Database Opening (Mode=Read/Write) up HomeSeer Energy database C:\Program Files\HomeSeer HS3\Data\Energy\Energy.hsd mai-25 09:55:58 Speech Listening for remote speaker connections on port 10401 mai-25 09:55:58 Startup Initializing Speaker Client Interface mai-25 09:55:58 Startup Start automation engine... mai-25 09:55:57 Startup Creating ASP.NET application host... mai-25 09:55:57 Web Server UPNP Discovery started mai-25 09:55:57 Web Server Web Server started on port 80 mai-25 09:55:57 Web Server Local IP address (subnet) is: 192.168.0.106 (255.255.255.0) mai-25 09:55:57 Z-Wave UZB1: Getting node information from controller... mai-25 09:55:57 Z-Wave UZB1: The Z-Wave API Execution Thread was Started or Restarted. mai-25 09:55:57 Plug-In Finished initializing plug-in Z-Wave mai-25 09:55:57 Z-Wave UZB1: The Z-Wave Command Execution Thread was Started or Restarted. mai-25 09:55:57 Z-Wave UZB1: ---------------------------------------------------------------------- mai-25 09:55:57 Z-Wave Initializing Z-Wave interface UZB1 (Z-Wave.me UZB) on COM7 mai-25 09:55:57 Z-Wave UZB1: ---------------------------------------------------------------------- mai-25 09:55:57 Z-Wave UZB1: ====================================================================== mai-25 09:55:57 Z-Wave 465 Simple AV Control Command Class Control Commands have been loaded successfully. mai-25 09:55:57 Z-Wave 0 event triggers were loaded from HomeSeer. mai-25 09:55:57 Z-Wave 0 event actions were loaded from HomeSeer. mai-25 09:55:56 Z-Wave 11 total Z-Wave Data Objects loaded. mai-25 09:55:56 Z-Wave Network 0E0D0C0B has 11 device data elements. mai-25 09:55:56 Z-Wave 1 Networks were restored from the data in the database... Building data connections. mai-25 09:55:56 Z-Wave Loading Z-Wave Data Objects... mai-25 09:55:56 Z-Wave 1 total Z-Wave Network Objects loaded. mai-25 09:55:56 Z-Wave Loading Z-Wave Network Objects... mai-25 09:55:56 Z-Wave Database: Opening (Mode=Read Only) up HomeSeer database C:\Program Files\HomeSeer HS3\Data\Z-Wave\Z-Wave2.db mai-25 09:55:55 Z-Wave InitIO called, plug-in version 3.0.1.87 is being initialized... mai-25 09:55:55 Info Plugin Z-Wave has connected. IP:127.0.0.1:49182 mai-25 09:55:54 Plug-In Finished initializing plug-in HSTouch Server mai-25 09:55:54 Info Plugin HSTouch Server has connected. IP:127.0.0.1:49180 mai-25 09:55:52 Startup Initializing Plug-Ins mai-25 09:55:52 Plug-In Found plug-in: Z-Wave, version: 3.0.1.87 mai-25 09:55:52 Plug-In Found plug-in: HSTouch Server, version: 3.0.0.68 mai-25 09:55:51 Startup Checking for available plug-ins mai-25 09:55:51 Info Remote plug-in API interface started on port 10400 mai-25 09:55:51 Startup This version of HomeSeer is registered as a HS3PRO version. mai-25 09:55:51 Startup Creating Speaker Client Interface Object... mai-25 09:55:51 Startup HomeSeer version is: 3.0.0.318 mai-25 09:55:51 Load Config Loading TIMERS... mai-25 09:55:51 Load Config Loading COUNTERS... mai-25 09:55:51 Load Config 2 total events loaded. mai-25 09:55:51 Load Config Loading Events... mai-25 09:55:51 Load Config Loading Event Groups... mai-25 09:55:51 Load Config 13 total devices loaded. mai-25 09:55:51 Database Loading Devices... mai-25 09:55:51 Database Opening (Mode=Read Only) up HomeSeer database C:\Program Files\HomeSeer HS3\Data\HomeSeerData.hsd mai-25 09:55:51 Startup Loading configuration file ... mai-25 09:55:51 Startup Database SAVE process started. mai-25 09:55:51 Startup Local voice recognition class started. mai-25 09:55:51 Startup HSPhone external interface class started. mai-25 09:55:51 Startup Plug-In Interface class started. mai-25 09:55:51 Startup E-Mail RECEIVE class started. mai-25 09:55:51 Startup E-Mail SEND class started. mai-25 09:55:51 Startup Web server class started. mai-25 09:55:51 Startup Application interface class started. mai-25 09:55:51 Startup COM port classes started. mai-25 09:55:51 Startup Creating Class Objects... mai-25 09:55:51 Startup mai-25 09:55:51 Startup ******************************************************************************** mai-25 09:55:51 Startup HomeSeer version 3.0.0.318 Edition: HS3 Pro Starting Now mai-25 09:55:51 Startup ******************************************************************************** mai-25 09:55:51 Startup mai-25 09:55:51 Startup Settings Loaded. Tusen takk for hjelp så langt. Endret 25. mai 2017 av Beerpal Siter
Moskus Skrevet 25. mai 2017 Skrevet 25. mai 2017 59 minutter siden, Beerpal skrev: men de synes ikke i "device list" Nei, det er er riktig. Denne bryteren kan kun styre andre Z-wave lys via assosiasjon. Det setter du opp under "Associations" (se det nederste skjermbildet ditt over). 1 Siter
Beerpal Skrevet 27. mai 2017 Forfatter Skrevet 27. mai 2017 Takk. Det skjønte ikke jeg! [emoji23] Jeg får teste dette ut mot en bryter. Så det betyr at man ikke kan lage en "Event"?Sent from my iPhone using Tapatalk Siter
Moskus Skrevet 27. mai 2017 Skrevet 27. mai 2017 2 timer siden, Beerpal skrev: Så det betyr at man ikke kan lage en "Event"? Nei. Assosiasjon (se HS-skolen del 4) er en node som styrer en annen. "Direkte", dvs. uten beskjeder som skal tolkes av master controller. 2 Siter
Beerpal Skrevet 28. mai 2017 Forfatter Skrevet 28. mai 2017 Den 27.5.2017 klokken 22.53, Moskus skrev: Nei. Assosiasjon (se HS-skolen del 4) er en node som styrer en annen. "Direkte", dvs. uten beskjeder som skal tolkes av master controller. Tusen takk for svar! Så man kan ikke lage en "virtuelle devicer" til direkte mot sånne brytere? PH Siter
INTIN RuneV Skrevet 29. mai 2017 Skrevet 29. mai 2017 Prøv å sette parameter 4 til 0 og gjør en rescan. Du skal få det opp slik: Siter
INTIN RuneV Skrevet 29. mai 2017 Skrevet 29. mai 2017 Var litt rask med forrige innlegg. Ser no at spørsmålet gjeld vanleg brytar og ikkje glassdimmar. For brytar er det assosiasjon som gjeld slik Moskus skriv 1 Siter
Moskus Skrevet 29. mai 2017 Skrevet 29. mai 2017 5 minutter siden, INTIN RuneV skrev: Var litt rask med forrige innlegg. Ser no at spørsmålet gjeld vanleg brytar og ikkje glassdimmar. For brytar er det assosiasjon som gjeld slik Moskus skriv Aaaaah! Pokker! Trodde du kom med gode nyheter nå... 10 timer siden, Beerpal skrev: Så man kan ikke lage en "virtuelle devicer" til direkte mot sånne brytere? Nei. 1 Siter
Anbefalte innlegg
Bli med i samtalen
Du kan publisere innhold nå og registrere deg senere. Hvis du har en konto, logg inn nå for å poste med kontoen din.